Mag drills online supplier in the United Kingdom from WeldingSuppliesDirect: The use of flux is a way to prevent chemical changes in the materials and to prevent inclusions, ensuring a stronger and more thorough fusion between materials. In welding, not all processes use flux. Some use flux in addition to a filler rod; others use a flux-cored filler. Many don’t use flux at all, but use a shielding gas to serve the same purpose. It depends largely on the process you’re using, and on the materials you’re fusing. Brazing makes heavy use of flux to ensure the chemical properties of the filler material allow it to be wicked into the joint via capillary action. Flux is a key part of brazing and the process generally can’t be done – or can’t easily be done – without it. Soldering sometimes uses flux, but it’s not always necessary. Flux will allow the solder to spread out and more comprehensively wet a surface, which can be important for larger and more effective electrical connections. However, in smaller uses and in purposes where a balled or dewetting solder isn’t a problem, flux isn’t necessary. In fact, a big part of learning how to solder is learning when flux is necessary and when it isn’t. Read additional info here Maxphotonics X1W-1500.

When you’re looking over different welding helmet options, you might come across the phrase “ANSI Approved.” ANSI is the regulating body that makes standards governing the performance of welding helmet shades, among many other things. The most recent standard comes from 2003 and is called ANSI Z87.1-2003. It specifies various tests a shade needs to pass to be certified. The key here is that many welding helmets were formerly ANSI-approved, but that was before the increased standards that came about in 2003. Make sure any helmet you choose meets the more modern version of helmet standards. There are a lot of basic welding masks on the market. These are simple frame-mounted masks that tilt up and down, have the most basic level of fixed-darkness shading, and have basically no additional protection for things like your neck, ears, or top of your head.

Staying informed about and compliant with local and national safety regulations is critical for any welding operation. This includes following guidelines set by occupational safety and health administrations and other relevant authorities. Compliance ensures that welding operations meet legal standards, which helps protect businesses from legal liabilities and fines, and more importantly, ensures a safe working environment for all employees. For those interested in deepening their knowledge of welding safety, resources such as the American Welding Society (AWS) website and safety publications can provide valuable information and updates.

I’m a huge fan of Makita’s cordless LXT range. The DGA452Z is one of the best angle grinders available right now, and it’s a bit of a beast. The grip shape is nice and narrow, with comfortable rubberised overmoulding on the rear handle. Once you’ve installed a battery it’s well balanced and doesn’t feel too heavy at 1.3 kg without a battery installed. The Makita cordless grinder has a powerful brushless motor that’s efficient as well as powerful. It puts out a whopping 11,000 rpm, which is incredibly impressive for a cordless grinder. When you pair it up with a high Ah battery, it squeezes every last drop of power and runs for a surprisingly long time. It features a soft start function, battery gauge, and overload protection as well. There’s an anti-restart function for added safety between battery changes. One of the most impressive features must be the automatic speed control though. The internal computer controls the power output according to the load conditions, which makes for better cuts and longer tool life.

UK market look: LOTOS Technology is a California company that has only been around since 2007. Still, the LOTOS MIG is impactful and high quality enough to make it onto our list. This one is a versatile machine that is a fair price of about $400. And—provided that you have the necessary 240-volt outlet in your home—it can be set up in a matter of minutes. The duty cycle of this welding newcomer is impressive, and it can be utilized by pros and amateurs who have been continually impressed by the bang they’ve gotten for their buck. The LOTOS can weld steel and stainless steel from 18 gauge to ¼ inches and aluminum to 1/8 inch or thicker. Thermal overload protection doesn’t let this machine overheat, and infinitely adjustable heat/amperage as well as wire speed makes using the LOTOS simple. Check out the LOTOS MIG140 for a lower power alternative.

Once you know how you’re going to be using your MIG welder, you’ll also need to think about what kind of weld you’re going to be doing. Consider the output of the machine that’s right for the kind of materials that you’ll be working with. The thicker the metal you work with, the more power you’re going to need in your MIG welder. Additionally, if a welder needs to use more than 100 volts, it will probably need a power supply. Ultimately, one of the main concerns that you’ll need to think about when choosing the right welder is how you’re going to make sure that your machine is safe and practical. There’s more to think about with a MIG welder than how you want the weld to look after you’re finished with it. However, if you’re looking for a clean finish, bear in mind that a Pulse MIG welder can reduce the risk of burning through your chosen metals. Read more info at weldingsuppliesdirect.co.uk.

Electron beam welding (EBW) is a fusion welding process where electrons generated by an electron gun are accelerated to high speeds. The electron beam creates kinetic heat as it contacts the base metals, causing them to melt and form a weld pool. A weld is created as the joint cools down. This welding procedure is performed in a controlled vacuum to prevent the beams from scattering. Electron beam welding offers precision, making it a valuable process for applications requiring minimal distortion. Some of its applications include electronic components, aircraft parts, storage tanks and bridge components. EBW allows to weld materials that are prone to contamination.

Important Industrial Gas Cylinder Safety Guidelines to Keep in Mind: Acetylene and oxygen are two industrial gases widely used across various industries. The cylinders accommodating these gases are designed with user’s safety in mind. However, that is not enough to ensure optimum safety in an industrial facility. The following factors will help ensure the same: Understand the Cylinder Properly: A personnel should be familiar with the potential risks and hazards associated with compressed gases while handling them. It is important to understand the properties of the gas filled within such as toxicity, flammability limits, and toxicity – Threshold Limit Value (TLV). Also, it is important to understand the hazards posed by gas at low temperature, high pressure or due to the physical state of the gas – non-liquefied or liquefied, etc. A personnel should read the contents of the label on the cylinder. If the label is missing or not easily readable, then the cylinder should not be used. In addition to improving a personnel’s understanding on oxygen cylinder safety or acetylene cylinder safety, he should be administered a proper plant safety training.

Do you feel frustrated because the disc grinder work is not progressing well, or you are running out of time? If that is your problem, then this Metal Cutting Disc will help you. It is a high-quality product that has been designed to provide ultimate performance. The wheels are made of steel and have a tooth count of 25. They are great for concrete, metal, or other materials where you want to cut through tough materials quickly. These discs are made from high-quality cutting wheels with a flat shape. They have a 3? diameter and a 1/16? thickness. With ultra-thin metal and stainless steel, they can quickly and easily cut through burrs and other unwanted materials. With these discs, you can grind metal and stainless steel fast and smooth while minimizing noise. As a versatile option for workshops, the discs can be used with sheet metal, die grinders, air cut off tools, and electric cut off tools.

The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.

One of the “cardinal sins” that almost every shop commits is over-welding. This means that if the drawing calls for a 1/4″ fillet weld, most shops will put down a 5/16″ weld. The reasons? Either they don’t have a fillet gauge and are not exactly sure of the size of the weld they are producing or they put in some extra to “cover” themselves and make sure there is enough weld metal in place. But, over-welding leads to tremendous consumable waste. Let’s look again at our example. For a 1/4″ fillet weld, the typical operator will use .129 lbs. per foot of weld metal. The 5/16″ weld requires .201 lbs. per foot of weld metal – a 56 percent increase in weld volume compared to what is really needed. Plus, you must take into account the additional labor necessary to put down a larger weld. Not only is the company paying for extra, wasted consumable material, a weld with more weld metal is more likely to have warpage and distortion because of the added heat input. It is recommended that every operator be given a fillet gauge to accurately produce the weld specified – and nothing more. In addition, changes in wire diameter may be used to eliminate over-welding.

How to pick a welder tips: Duty cycle: The advertised amperage of the machine offers a headline guide, but the duty cycle of the machine gives up the truth. Light industrial machine duty cycles can be as low as 20%, but more heavy duty MIG’s should range between 40-60%. If a 300amp MIG has 30% duty cycle for instance, it’s on the edge of acceptability. Duty cycle is determined by how many minutes out of 10, it can weld at 100%. Duty cycle testing: MIGS tested at 20 Degrees & 40 Degrees we consider good. (Beware any manufacturer who doesn’t quote an ambient temperature for testing) Manufacturer’s warranty: Always a great guide to quality. A three year warranty is good. Weld characteristics: Make sure the arc is smooth & suits your application. (Some machines are better suited at the low range and others at higher amperage range).

A few advices about welding equipment, MIG and TIG welders, plasma cutters. MIG Welders are extremely popular because they tend to cost less than TIG or Stick welders with comparable power and features, are extremely easy to learn, and can tackle a wide variety of projects. Since the filler metal is fed through the MIG welding torch, welders can use both hands to hold the torch steady rather than using one hand to add filler metal, as in TIG welding. The wire feeder also makes MIG welding up to four times faster. The MIG welding process uses an inert gas to shield the weld and to keep it free from impurities. This makes MIG welding very neat and easy to clean up since there isn’t anything to chip away, which is typical for Stick welding. MIG welding can be used on a wide variety of materials such as aluminum and is also frequently used for automotive work. However, MIG also requires the purchase of shielding gas and generally requires materials that cost more when compared to other methods.

MaxxAir HVHF 12COMBO Heavy Duty Cylinder Fan with 20-foot Vinyl Hose. Maxx Air has been producing high-quality ventilation systems since 1948 for industrial and residential areas. This cylinder fan is one of their powerful and efficient fume extractors that you can use anywhere you want. Extremely Lightweight and Industrial Finishing. This compact and lightweight machine weighs only 1.02 pounds despite its large size. It’s built with high-quality steel material that makes it sturdy and robust. With painted finishing and buttoned control, the air cylinder fan gives a vintage and industrial look. 2000 CFM Airflow and 20-foot Long Vinyl Hose. Maxx Air HVHF can efficiently replace any ventilation system that your workplace or residence has. It can generate 2000 CFM airflow with 120V power. The vinyl hose is 20 feet long and adjusted to a high-velocity blower.

This drill, though not quite as advanced as our top pick, will be an excellent addition to your arsenal. It is a lightweight mag drill that comes with a swivel base magnet, making it easy to use during horizontal or overhead jobs. The HMD904S has a powerful 7.2A motor and you can drill holes with a diameter of up to 1.5” and up to 2” deep. This drill is incredibly versatile and features a two-stage magnet that increases power by up to 30%. The drill is also fitted with a pilot light, making it possible to do accurate work, even in conditions with inadequate lighting. For added convenience and accuracy, the drill is fitted with a slot drive arbor, making it quicker to change out accessories. This drill is designed for industrial and heavy-duty applications. You will be able to drill thousands of holes with no problems whatsoever. As a versatile tool, this drill is perfect for the casual handyman as well as the professional steelworker.

The story of ESAB is the story of welding. When our founder Oscar Kjellberg developed the world’s first coated welding electrode in 1904, he launched a company whose innovation and uncompromising standards have helped create the history of welding itself. For more than 100 years, ESAB has been powered by the will to continuously seek new and improved ways of serving our customers. This has made ESAB a world leader in welding products and advanced cutting systems. In 2012, ESAB was acquired by Colfax Corporation, one of the world’s leading diversified industrial manufacturing companies. Colfax, like ESAB, is a solidly customer-focused company that places strong emphasis on constant innovation and improvement. From the firsts by our founder to our global growth, we take pride in what we’ve accomplished in more than a century. But we do so with a keen eye on the future. What can we do better? It’s only when we seek to build upon all we’ve learned, to perfect the innovations our customers count on to work confidently, and push ourselves and our company further that we can boldly face the future. This is how we continue to write the history of welding and cutting. At the end of the day, it’s not where you’ve been that matters most – it’s where you’re going. And for us, that’s forward.

Welding Supplies Direct are the UK distributor for GPPH welding tables, manufactured to the highest standards in Europe. GPPH’s range of welding benches and tables are laser cut for precision and are used in every branch of industry. These welding tables offer perfect flatness (+/- 0.5MM) & are made from 15MM thick S355J2+N grade steel. Our modular welding benches come equipped with a hole system of all sides (tabletop & all sides); the holes are 28MM in diameter and have a chamfered edge for easy tool assembly. You have the option of standard legs or castors being fitted, too.

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

The people behind Display4top market this particular model as a professional MIG welder and we can’t say that they make a poor case in that regard. For one, its duty cycle is definitely up there. With its 48A rated output, the model is able to work for 6 minutes straight before overheating. It comes equipped with a variable wire speed control trigger, so you’ll be able to efficiently work with different metals. There are two power settings and an Ampere knob, further making the versatility case. More importantly, the model is as durable as they come. The forced air cooling system keeps the temperature at a nice, practical level. On top of that, the welder incorporates a thermal overload protection system that will be able to pick up the former’s slack in case it fails to do its job.